# Régulation de pH

**<span style="vertical-align: inherit;"><span style="vertical-align: inherit;">La régulation du pH</span></span>**

**Objectif du projet :**

<span style="font-weight: 400;">Le projet consiste à réguler le pH d’une certaine solution (acide ou basique) en utilisant un programme Arduino. L’idée vient du problème de neutralisation des rejets liquides industriels qui consiste une étape primordiale dans le traitement des déchets.</span>

<span style="vertical-align: inherit;">  
</span>

**Le matériel utilisé :**

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">4 bouteilles en plastique (2 réservoirs pour l’acide et la base, un réacteur, et un tank).</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">3 électrovannes associées à des relais.</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Une sonde de pH</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Une Tige d’agitation associé à un moteur</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Un afficheur</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Un indicateur de niveau</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Un Arduino avec une plaque d’essai</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Des files et des tuyaux en plastique </span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Un support en bois </span>

**Les appareils utilisés :**

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Découpeuse Laser </span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Perceuse à colonne</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Scie électrique</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Imprimante 3D</span>

<span style="font-weight: 400;">-</span><span style="font-weight: 400;"> </span><span style="font-weight: 400;">Des outils manuels ( pistolet à colle, perceuse, viceuse à main,…)</span>

**Les étapes de construction :**

<span style="font-weight: 400;">**Étape 1** : Construction du support </span>

<span style="font-weight: 400;">Nous avons utilisé 4 plaques ( 60</span><span style="font-weight: 400;">30 cm^2) pour avoir un support 90</span><span style="font-weight: 400;">60.</span>

<span style="font-weight: 400;">**Étape 2** : Mise en place des réservoirs</span>

<span style="font-weight: 400;">Nous avons fixé d’abord les 2 réservoirs des solutions acide et base. Ensuite, nous avons fixé le réacteur et le tank. Enfin, nous avons fait des trous pour faire passer les tuyaux.</span>

<span style="font-weight: 400;">**Étape 3** : Mise en place des électrovannes </span>

<span style="font-weight: 400;">Nous avons placé les électrovannes à la sortie des deux réservoirs ainsi que le réacteur.</span>

<span style="font-weight: 400;">Nous avons associé à ces dernières des relais.</span>

<span style="font-weight: 400;">**Étape 4** : Impression de la tige</span>

<span style="font-weight: 400;">Nous avons fait le design de la tige en utilisant le logiciel Tinkercad, et ensuite nous avons utilisé l'imprimante 3D. Enfin, nous avons relié la tige au moteur.</span>

<span style="font-weight: 400;">  
  
</span>